How to Fix A Leaky Flange Gasket on A Toilet
Leaking flange gasket
If you see water on the floor around the toilet, first make an effort to figure out whether or not it is from leaking toilet bolts just condensation. In the event you cannot locate the source or if more water appears with every use, the water is possibly coming from the floor flange. Right the situation as soon as achievable as water can deal laminate plywood, blister underlayment, and rot the subfloor of your bathroom.
Quick fix: if the toilet was installed within the past couple of months, then merely tightening the closet bolts on the base of the toilet might reseal the bowl's wax gasket. New ask gaskets nearly usually compress a bit after installation, which can leave the bolts loose. Continued use can then use the toilet to rock in location, breaking the seal. There is frequently sufficient wax you develop a new seal but only should you can draw the toilet floor flange together.
Start by popping the caps from the closet bolts at the base of the toilet. Try under them with this crew driver or putty knife. Now that the caps have been removed, use a small ranch to test the tightness of the knots. If they turn easily, tighten them only until they really feel snug after which watch the base of the toilet carefully over the next few days. If the floor stays dry, you've solve the problem!
Replacing the Gasket: If water reappears or if the bolts had been snug within the first place, you may need to take up the toilet and install a new wax gasket and closet bolts. If your toilet has been in place for years, don't anticipate a quick fix to work. You will need to replace the wax gasket at the very first sign of any water trouble.
Fixing Broken Flanges
Plastic toilet flanges are sturdy and seldom fail under regular conditions. Flanges produced of cast iron and cast brass on the other hand, are much more vulnerable to break. The slotted portion of the flange is fairly narrow so the slightest casting flaw will weaken it further. It is straightforward to break a flange by over tightening the closet bolts but in time, even normally used in break a weak flange.
Step 1: when a flange breaks, the bolts on that side drifts outward loosening its grip on the flange. The toilet begins to feel loose; rocking in location would he sit on it. This movement soon breaks a gasket seal and also the toilet leaks within each flush.
If this takes place, don't panic since there is a fairly easy solution. Replacing the whole flange is the most expert factor to do but doing so demands cutting and splicing drainpipe or replacing cast-iron fittings-which is really a big job. The simpler solution is really a repair strap that works surprisingly nicely. The crescent shaped strap mirrors the shape of the flange and has an opening for a closet bowl. To use his strap, 1st remove the toilet. Insert a closet bowl by means of the repair strap; slide the strap under the old flange, next to the break and install the wax gasket at that time.
Step 2: if the strap won't slide under the flange, loosen the floor screws and using the flange slightly with the pry bar. When you get the strap in place, read tighten the screws.
Flange breaks involve little sections of metal, so there's generally sufficient flange leftist support the repair strap. It's a nice little trick and one that saves hours of function for the do it oneself plumber.
How to Fix A Leaky Flange Gasket on A Toilet
Best Balloon Car
Video Clips. Duration : 1.92 Mins.
Best Balloon Car
made from 1/2 in. insulation board, straws, plumbers putty, short piece of 1/2 in flexible hose from Lowe's, with axles, axle holders and CD wheels from a "mouse trap car" kit purchased at Hobby Lobby. Axle and wheel alignment are critical. Similar to building pinewood derby car in Boy Scouts. Use graphite powder to reduce friction at axle housings. Put the clear tubing into the balloon and extending through the body. Pack the putty around the straws where inserted into the tubing, and tape it tightly. Place 4 straws upright on the corners of the body to keep the deflating balloon from falling on the wheels. Use smaller wheels, like mini CDs for quicker take off - increase deflation rate of balloon to increase starting speed. We went for a straight running car to go a long distance. It worked. We Won! Hope you do too. Visit Lonnie's voice and violin work at easleyls
Best Balloon Car
Best Balloon Car
Best Balloon Car
Best Balloon Car
No URL Best Balloon Car
Where to Place Knobs on a Cabinet
Once you decide to change out cabinet hardware you might find the style you pick won't look that great if you try and replace the knobs in the same spots that the old ones were in. Well what to do? You certainly don't want to go back to the same boring old hardware. Instead you need a better understanding of your options for where to place knobs on a cabinet.
The most obvious place to put a knob will be on a side opposite a hinge. The leverage allows you to open the door with almost no effort. This is great for those that might have a disability limiting their grip strength. The only exception to this rule is if you have roll out bottom cabinets, you know, the giant drawer types. Those you'll want to install the knobs centered on the cabinet to keep it from binding up on either side.
Well that gives you a rough idea of where to put the knobs but you probably need something a little bit more exact. Unfortunately there's no magic formula for where to place knobs on a cabinet. It's all going to come down to how the cabinets are designed and the size and shape of them and your kitchen.
There's a trick you can use to figure out where to place the knobs without just randomly drilling a bunch of holes into the cabinet face and hoping for the best. Head out to the hardware store and pick up a small tub of plumber's putty. Plumbers putty is a non-hardening compound that's slightly tacky. You can pull off little dollops of it then use it to just stick the knobs to the cabinet.
Here's what you'll do.
Open up the tub of Plumber's putty.
Pinch off a piece of putty about the size of the tip of your thumb.
Roll it into a ball.
Take the cabinet hardware and press the putty onto the back of it. Now you can just stick the knob onto the cabinet face wherever you think it will look right. Repeat this for a couple of the doors so you can get an overall feel for how the knobs will look sitting in a row. You can reposition the knobs just by popping them off the cabinet face and sticking them back on in a new spot.
Once you've figured out the right look for the cabinet you'll need to measure the knob offsets from the bottom and side edge of the cabinets. You can then use those measurements as a template for knob placement. Mark the offsets on each of the cabinets and double check to make sure they aren't slanting up or down.
The last thing to do is attach the hardware. Just drill the holes in the cabinet and slide a bolt through the hole and tighten the knobs down onto it. It's all a pretty simple job. Where to place knobs on a cabinet is a completely personal choice. You'll know what looks right once you get the knobs in position.
Where to Place Knobs on a Cabinet
REMOVING A 35 YEAR OLD TUB DRAIN
Video Clips. Duration : 2.78 Mins.
REMOVING A 35 YEAR OLD TUB DRAIN
A VERY ROUGH VIDEO (AND PICS) ON HOW I REMOVED OUR OLD DRAIN THAT ORIGINALLY CAME WITH THE HOUSE WHEN IT WAS BUILT IN 1977. MATERIALS AND TOOLS: One SMALL PLIER, one 12" CHANNEL LOCK PLIERS, PLUMBERS PUTTY, CHROME ROLLER BALL DRAIN SET, HUMAN MUSCLES. I ORIGINALLY NEVER PLANNED TO MAKE A HOW-TO VIDEO, SO SOME VIDEO FOOTAGE THAT WAS MISSING WAS SUBSTITUTED WITH PICTURES. DISCALIMER: THIS VIDEO WAS INTENDED FOR THOSE WITH OLD TUB DRAINS WHERE THE CROSS BARS ARE STILL INTACT AND ASSUMING THAT THE OLD DRAIN WAS INSTALLED CORRECTLY. IF YOU FEEL THAT YOU MAY DAMAGE THE TUB SHOE, DO NOT PROCEDE. UNLESS YOU KNOW HOW TO DEAL WITH THE CONSEQUENCES, CALL A TRUSTED PLUMBER.
REMOVING A 35 YEAR OLD TUB DRAIN
REMOVING A 35 YEAR OLD TUB DRAIN
REMOVING A 35 YEAR OLD TUB DRAIN
REMOVING A 35 YEAR OLD TUB DRAIN
No URL REMOVING A 35 YEAR OLD TUB DRAIN
Handling Your Own Shower Drain Installation Project
Upgrading a bathroom is one of the more popular home improvement projects. Handling the plumbing for draining your shower can be exceedingly simple unless you go overboard.
Whether you are a bathtub or shower person, most people look for shower only options when buying a home. This simple fact means more than a few homeowners spend a weekend upgrading or installing showers in their bathrooms. Fortunately for you, it is a fairly simple process.
A collector or pan refers to the horizontal surface located at the bottom of the shower. The collector typically consists of a non-slip surface slightly banked towards the center or wherever the drain is located. Combined with three to four inch walls around the side, the goal of your shower drainage plumbing is to get the water to flow to and down the drain.
You can physically build a collector for your new shower, but you really need to think about it. Do you really want to get into the complications of getting the sloping correct, not to mention making sure every aspect of it is waterproof? And I mean every aspect! It is much easier to simply buy a pre-cast collector online or at your local Lowes, Home Depot or hardware store. Building one might sound like a great idea, but you will probably feel differently after a couple of hours.
Regardless of how you go about getting a pan, you should make every effort to use one that has the drain located in the same spot as the original pan. Moving the drain pipes can be a task, particularly if the builder used a unique framing structure. If you are determined to move the drain, you are going to have to cut back the pipe or lengthen it, which may mean ripping up large chunks of the floor. Put another way, you are going to be looking at a multiple weekend project.
Assuming we have our drain lined up, the actual hook up is fairly simple. The drainage pipe should be facing vertical up to the collector. It will often look like a "U", which means it acts as a cleanout to keep nasty smells from coming back up from the drain. To connect the drain, you are going to create a water tight connection between a drain cap on the top of the pan and the drainage pipe. Systems vary, but you are typically going to do this by putting a coupling piece on the top of the drainage pipe. This is then covered with gaskets and literally screwed into the drain cap. The drain cap should act as a locknut, to wit, it screws directly onto the coupling.
The tricky part of this process is getting your drain cap to fit into a watertight position in the pan. This is accomplished by backing off the drain cap once you are sure everything fits together. At that point, you put plumbers putty around the underside of the cap and then screw it back on. The putty should form a tight seal between the cap and the shower pan, which keeps water from trickling under it and into the framing under the shower.
Obviously, bathroom showers come in a wide variety of styles these days. If you purchase a collector, they almost always come with plumbing instructions or the store can note anything unusual you should know. It sounds complex, but is typically pretty straight forward. Have fun!
Handling Your Own Shower Drain Installation Project
HOW TO: Replace an RV Plumbing Vent
Video Clips. Duration : 9.28 Mins.
HOW TO: Replace an RV Plumbing Vent
We demonstrate how to replace a plumbing vent cap on the roof of an RV. Sun and age can lead to cracked plumbing vent covers on the roof of an RV, travel trailer or fifth wheel. Installing a new vent is a quick easy job, completed with just a few simple tools. Older style roof vents may not match replacement vents, which makes it impossible to simply snap a new cap onto an older vent base. This means having to replace the base, even if it's in good condition. A little Dicor (readily available from Camping World or RV parts & service facility) will seal the new vent. ensuring that your camper stays dry. This is a quick, easy repair, completed without special skills in under half an hour. A new roof vent cover currently costs about , and a tube of Dicor should be about at your local camping store. This was done on the fiberglass roof of a Newmar Mountain Aire diesel pusher, but is handled the same way on an EPDM rubber roof. Be sure to confirm that all methods and materials used are compatible with your particular RV. RV Geeks offers basic DIY (do it yourself) RV service, repair and maintenance tips from full-time RVers who have been handling most of their own maintenance since hitting the road in 2003. RVgeeks is proud to be affiliated with RVtravel.com. www.rvtravel.com While we're not RV technicians, we're very mechanically inclined and have learned a lot about RV systems over the years. We handle most of our own minor service, maintenance and repair work on our ...
HOW TO: Replace an RV Plumbing Vent
HOW TO: Replace an RV Plumbing Vent
HOW TO: Replace an RV Plumbing Vent
HOW TO: Replace an RV Plumbing Vent
No URL HOW TO: Replace an RV Plumbing Vent
Handling Your Own Shower Drain Installation Project
Upgrading a bathroom is one of the more popular home improvement projects. Handling the plumbing for draining your shower can be exceedingly simple unless you go overboard.
Whether you are a bathtub or shower person, most people look for shower only options when buying a home. This simple fact means more than a few homeowners spend a weekend upgrading or installing showers in their bathrooms. Fortunately for you, it is a fairly simple process.
A collector or pan refers to the horizontal surface located at the bottom of the shower. The collector typically consists of a non-slip surface slightly banked towards the center or wherever the drain is located. Combined with three to four inch walls around the side, the goal of your shower drainage plumbing is to get the water to flow to and down the drain.
You can physically build a collector for your new shower, but you really need to think about it. Do you really want to get into the complications of getting the sloping correct, not to mention making sure every aspect of it is waterproof? And I mean every aspect! It is much easier to simply buy a pre-cast collector online or at your local Lowes, Home Depot or hardware store. Building one might sound like a great idea, but you will probably feel differently after a couple of hours.
Regardless of how you go about getting a pan, you should make every effort to use one that has the drain located in the same spot as the original pan. Moving the drain pipes can be a task, particularly if the builder used a unique framing structure. If you are determined to move the drain, you are going to have to cut back the pipe or lengthen it, which may mean ripping up large chunks of the floor. Put another way, you are going to be looking at a multiple weekend project.
Assuming we have our drain lined up, the actual hook up is fairly simple. The drainage pipe should be facing vertical up to the collector. It will often look like a "U", which means it acts as a cleanout to keep nasty smells from coming back up from the drain. To connect the drain, you are going to create a water tight connection between a drain cap on the top of the pan and the drainage pipe. Systems vary, but you are typically going to do this by putting a coupling piece on the top of the drainage pipe. This is then covered with gaskets and literally screwed into the drain cap. The drain cap should act as a locknut, to wit, it screws directly onto the coupling.
The tricky part of this process is getting your drain cap to fit into a watertight position in the pan. This is accomplished by backing off the drain cap once you are sure everything fits together. At that point, you put plumbers putty around the underside of the cap and then screw it back on. The putty should form a tight seal between the cap and the shower pan, which keeps water from trickling under it and into the framing under the shower.
Obviously, bathroom showers come in a wide variety of styles these days. If you purchase a collector, they almost always come with plumbing instructions or the store can note anything unusual you should know. It sounds complex, but is typically pretty straight forward. Have fun!
Handling Your Own Shower Drain Installation Project
Mighty Putty Sucks As Seen On TV
Tube. Duration : 2.95 Mins.
Mighty Putty Sucks As Seen On TV
Mr. Dupre installs mighty putty on a small crack in the pvc pipe. Product does not work as advertised. Might Putty Sucks.
Mighty Putty Sucks As Seen On TV
Mighty Putty Sucks As Seen On TV
Mighty Putty Sucks As Seen On TV
Mighty Putty Sucks As Seen On TV
No URL Mighty Putty Sucks As Seen On TV
Handling Your Own Shower Drain Installation Project
Upgrading a bathroom is one of the more popular home improvement projects. Handling the plumbing for draining your shower can be exceedingly simple unless you go overboard.
Whether you are a bathtub or shower person, most people look for shower only options when buying a home. This simple fact means more than a few homeowners spend a weekend upgrading or installing showers in their bathrooms. Fortunately for you, it is a fairly simple process.
A collector or pan refers to the horizontal surface located at the bottom of the shower. The collector typically consists of a non-slip surface slightly banked towards the center or wherever the drain is located. Combined with three to four inch walls around the side, the goal of your shower drainage plumbing is to get the water to flow to and down the drain.
You can physically build a collector for your new shower, but you really need to think about it. Do you really want to get into the complications of getting the sloping correct, not to mention making sure every aspect of it is waterproof? And I mean every aspect! It is much easier to simply buy a pre-cast collector online or at your local Lowes, Home Depot or hardware store. Building one might sound like a great idea, but you will probably feel differently after a couple of hours.
Regardless of how you go about getting a pan, you should make every effort to use one that has the drain located in the same spot as the original pan. Moving the drain pipes can be a task, particularly if the builder used a unique framing structure. If you are determined to move the drain, you are going to have to cut back the pipe or lengthen it, which may mean ripping up large chunks of the floor. Put another way, you are going to be looking at a multiple weekend project.
Assuming we have our drain lined up, the actual hook up is fairly simple. The drainage pipe should be facing vertical up to the collector. It will often look like a "U", which means it acts as a cleanout to keep nasty smells from coming back up from the drain. To connect the drain, you are going to create a water tight connection between a drain cap on the top of the pan and the drainage pipe. Systems vary, but you are typically going to do this by putting a coupling piece on the top of the drainage pipe. This is then covered with gaskets and literally screwed into the drain cap. The drain cap should act as a locknut, to wit, it screws directly onto the coupling.
The tricky part of this process is getting your drain cap to fit into a watertight position in the pan. This is accomplished by backing off the drain cap once you are sure everything fits together. At that point, you put plumbers putty around the underside of the cap and then screw it back on. The putty should form a tight seal between the cap and the shower pan, which keeps water from trickling under it and into the framing under the shower.
Obviously, bathroom showers come in a wide variety of styles these days. If you purchase a collector, they almost always come with plumbing instructions or the store can note anything unusual you should know. It sounds complex, but is typically pretty straight forward. Have fun!
Handling Your Own Shower Drain Installation Project
DIY Shower Drain Connection/How To Replace/Fix Leaky Drain in 2nd Floor Shower
Video Clips. Duration : 17.33 Mins.
DIY Shower Drain Connection/How To Replace/Fix Leaky Drain in 2nd Floor Shower
WE DID IT! Without any plumbing experience, hubby and I figured it out and replaced a portion of our shower drain pipe and connected a brand new brass drain. Everything here, step by step. YOU CAN DO IT TOO! More of my projects on mossisawesome.wordpress.com
DIY Shower Drain Connection/How To Replace/Fix Leaky Drain in 2nd Floor Shower
DIY Shower Drain Connection/How To Replace/Fix Leaky Drain in 2nd Floor Shower
DIY Shower Drain Connection/How To Replace/Fix Leaky Drain in 2nd Floor Shower
DIY Shower Drain Connection/How To Replace/Fix Leaky Drain in 2nd Floor Shower
No URL DIY Shower Drain Connection/How To Replace/Fix Leaky Drain in 2nd Floor Shower
Handling Your Own Shower Drain Installation Project
Upgrading a bathroom is one of the more popular home improvement projects. Handling the plumbing for draining your shower can be exceedingly simple unless you go overboard.
Whether you are a bathtub or shower person, most people look for shower only options when buying a home. This simple fact means more than a few homeowners spend a weekend upgrading or installing showers in their bathrooms. Fortunately for you, it is a fairly simple process.
A collector or pan refers to the horizontal surface located at the bottom of the shower. The collector typically consists of a non-slip surface slightly banked towards the center or wherever the drain is located. Combined with three to four inch walls around the side, the goal of your shower drainage plumbing is to get the water to flow to and down the drain.
You can physically build a collector for your new shower, but you really need to think about it. Do you really want to get into the complications of getting the sloping correct, not to mention making sure every aspect of it is waterproof? And I mean every aspect! It is much easier to simply buy a pre-cast collector online or at your local Lowes, Home Depot or hardware store. Building one might sound like a great idea, but you will probably feel differently after a couple of hours.
Regardless of how you go about getting a pan, you should make every effort to use one that has the drain located in the same spot as the original pan. Moving the drain pipes can be a task, particularly if the builder used a unique framing structure. If you are determined to move the drain, you are going to have to cut back the pipe or lengthen it, which may mean ripping up large chunks of the floor. Put another way, you are going to be looking at a multiple weekend project.
Assuming we have our drain lined up, the actual hook up is fairly simple. The drainage pipe should be facing vertical up to the collector. It will often look like a "U", which means it acts as a cleanout to keep nasty smells from coming back up from the drain. To connect the drain, you are going to create a water tight connection between a drain cap on the top of the pan and the drainage pipe. Systems vary, but you are typically going to do this by putting a coupling piece on the top of the drainage pipe. This is then covered with gaskets and literally screwed into the drain cap. The drain cap should act as a locknut, to wit, it screws directly onto the coupling.
The tricky part of this process is getting your drain cap to fit into a watertight position in the pan. This is accomplished by backing off the drain cap once you are sure everything fits together. At that point, you put plumbers putty around the underside of the cap and then screw it back on. The putty should form a tight seal between the cap and the shower pan, which keeps water from trickling under it and into the framing under the shower.
Obviously, bathroom showers come in a wide variety of styles these days. If you purchase a collector, they almost always come with plumbing instructions or the store can note anything unusual you should know. It sounds complex, but is typically pretty straight forward. Have fun!
Handling Your Own Shower Drain Installation Project
Bath bore Repair and alter allotment 4 of 8
Tube. Duration : 8.03 Mins.
Bath bore Repair and alter allotment 4 of 8
www.plumberx.comHello this is PlumberX. People always ask me what gave you the idea and what made you create these how to plumbing videos? Coming up with the idea was easy. After many years as a plumber and servicing customers at there home I've seen a lot of people in tuff situations, people that could not afford a plumber, people that didn't have time to wait for a plumber to come to there home and make repairs, hearing horror stories of Plumbers that have rip off costumers and gave bad service, to me this was a loud cry for help. One story come to mind; A friend of mine calls me and ask, PlumberX could you do me a favor and help this older lady that I know, and go by and look at her Plumbing, she needs plumbing work really bad but she's to scared to call a plumber because of the cost, and she know that if I send you over there to check out the plumbing she can trust me as a friend recommending you, sure I said I could do that. The next day came and I went to the older lady's home she came to the door with a pleasant smile very humble. I could see it in her eye's she didn't have to say a word ( What is this going to cost ) she was very polite and courteous. Sir would you like some thing to drink and I do appreciate you coming to check out my plumbing on such short notice. No problem mam, lets see what's going on here with your plumbing. This way Sir in the kitchen. As I walk through the home I saw in the corner of my eye younger children around 3, 5 and 6 years of age ...
Bath bore Repair and alter allotment 4 of 8
Bath bore Repair and alter allotment 4 of 8
Bath bore Repair and alter allotment 4 of 8
Bath bore Repair and alter allotment 4 of 8
No URL Bath bore Repair and alter allotment 4 of 8
www.plumberx.comHello this is PlumberX. People always ask me what gave you the idea and what made you create these how to plumbing videos? Coming up with the idea was easy. After many years as a plumber and servicing customers at there home I've seen a lot of people in tuff situations, people that could not afford a plumber, people that didn't have time to wait for a plumber to come to there home and make repairs, hearing horror stories of Plumbers that have rip off costumers and gave bad service, to me this was a loud cry for help. One story come to mind; A friend of mine calls me and ask, PlumberX could you do me a favor and help this older lady that I know, and go by and look at her Plumbing, she needs plumbing work really bad but she's to scared to call a plumber because of the cost, and she know that if I send you over there to check out the plumbing she can trust me as a friend recommending you, sure I said I could do that. The next day came and I went to the older lady's home she came to the door with a pleasant smile very humble. I could see it in her eye's she didn't have to say a word ( What is this going to cost ) she was very polite and courteous. Sir would you like some thing to drink and I do appreciate you coming to check out my plumbing on such short notice. No problem mam, lets see what's going on here with your plumbing. This way Sir in the kitchen. As I walk through the home I saw in the corner of my eye younger children around 3, 5 and 6 years of age ...
Keywords:
Plumbers Putty
Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project
WE DID IT! Without any plumbing experience, hubby and I figured it out and replaced a portion of our shower drain pipe and connected a brand new brass drain. Everything here, step by step. YOU CAN DO IT TOO! More of my projects on mossisawesome.wordpress.com
Tags:
Plumbers Putty
Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project
Mr. Dupre installs mighty putty on a small crack in the pvc pipe. Product does not work as advertised. Might Putty Sucks.
Tags:
Plumbers Putty
Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project
We demonstrate how to replace a plumbing vent cap on the roof of an RV. Sun and age can lead to cracked plumbing vent covers on the roof of an RV, travel trailer or fifth wheel. Installing a new vent is a quick easy job, completed with just a few simple tools. Older style roof vents may not match replacement vents, which makes it impossible to simply snap a new cap onto an older vent base. This means having to replace the base, even if it's in good condition. A little Dicor (readily available from Camping World or RV parts & service facility) will seal the new vent. ensuring that your camper stays dry. This is a quick, easy repair, completed without special skills in under half an hour. A new roof vent cover currently costs about , and a tube of Dicor should be about at your local camping store. This was done on the fiberglass roof of a Newmar Mountain Aire diesel pusher, but is handled the same way on an EPDM rubber roof. Be sure to confirm that all methods and materials used are compatible with your particular RV. RV Geeks offers basic DIY (do it yourself) RV service, repair and maintenance tips from full-time RVers who have been handling most of their own maintenance since hitting the road in 2003. RVgeeks is proud to be affiliated with RVtravel.com. www.rvtravel.com While we're not RV technicians, we're very mechanically inclined and have learned a lot about RV systems over the years. We handle most of our own minor service, maintenance and repair work on our ...
Keywords:
Plumbers Putty
Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project
A VERY ROUGH VIDEO (AND PICS) ON HOW I REMOVED OUR OLD DRAIN THAT ORIGINALLY CAME WITH THE HOUSE WHEN IT WAS BUILT IN 1977. MATERIALS AND TOOLS: One SMALL PLIER, one 12" CHANNEL LOCK PLIERS, PLUMBERS PUTTY, CHROME ROLLER BALL DRAIN SET, HUMAN MUSCLES. I ORIGINALLY NEVER PLANNED TO MAKE A HOW-TO VIDEO, SO SOME VIDEO FOOTAGE THAT WAS MISSING WAS SUBSTITUTED WITH PICTURES. DISCALIMER: THIS VIDEO WAS INTENDED FOR THOSE WITH OLD TUB DRAINS WHERE THE CROSS BARS ARE STILL INTACT AND ASSUMING THAT THE OLD DRAIN WAS INSTALLED CORRECTLY. IF YOU FEEL THAT YOU MAY DAMAGE THE TUB SHOE, DO NOT PROCEDE. UNLESS YOU KNOW HOW TO DEAL WITH THE CONSEQUENCES, CALL A TRUSTED PLUMBER.
Keywords:
Plumbers Putty
Where to Place Knobs on a Cabinet
Plumbers Putty
made from 1/2 in. insulation board, straws, plumbers putty, short piece of 1/2 in flexible hose from Lowe's, with axles, axle holders and CD wheels from a "mouse trap car" kit purchased at Hobby Lobby. Axle and wheel alignment are critical. Similar to building pinewood derby car in Boy Scouts. Use graphite powder to reduce friction at axle housings. Put the clear tubing into the balloon and extending through the body. Pack the putty around the straws where inserted into the tubing, and tape it tightly. Place 4 straws upright on the corners of the body to keep the deflating balloon from falling on the wheels. Use smaller wheels, like mini CDs for quicker take off - increase deflation rate of balloon to increase starting speed. We went for a straight running car to go a long distance. It worked. We Won! Hope you do too. Visit Lonnie's voice and violin work at easleyls
Tags:
Plumbers Putty
How to Fix A Leaky Flange Gasket on A Toilet
Plumbers Putty
